技术规格
薄膜技术参数
主要牌号的关键技术参数:厚度、拉伸强度、雾度、光泽度、表面张力与幅宽范围。所有数值为典型值,可按客户要求定制。
BOPP 普通薄膜技术参数表 /
基础信息 /
- 执行标准 /
- QB/T 2713-2005
- 商品编码 /
- 3920201000
- 型号规格 /
- BOPP Plain 20µm
- 卷号 /
- BP230815001
- 原材料 /
- PP K8303 / K7726
- 生产日期 /
- 2023-08-15
- 测试日期 /
- 2023-08-18
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 参数 | Unit | Value / Range | Standard |
|---|---|---|---|
| 厚度 | μm | 3 – 75 | GB/T 13950 |
| 纵向拉伸强度 | N/15mm | ≥ 10 | GB/T 1040 |
| 横向拉伸强度 | N/15mm | ≥ 8 | GB/T 1040 |
| Elongation at Break MD | % | 50 – 200 | GB/T 1040 |
| 雾度 | % | ≤ 1.5 | GB/T 2410 |
| 光泽度 | GU | ≥ 85 | GB/T 8807 |
| 表面张力 | mN/m | ≥ 38 | GB/T 14216 |
| 幅宽 | mm | 250 – 10,000 | Custom |
| 纸芯 | inch | 1″ 2″ 3″ 6″ | Standard |
| 卷长 | m | 200 – 8,000 | Custom |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
BOPP 热封薄膜技术参数表 /
基础信息 /
- 执行标准 /
- QB/T 2713-2005
- 商品编码 /
- 3920201000
- 型号规格 /
- BOPP Heat Seal 25µm
- 卷号 /
- HS230901002
- 原材料 /
- PP K8303 + Seal Layer
- 生产日期 /
- 2023-09-01
- 测试日期 /
- 2023-09-05
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 参数 | Unit | Value | Notes |
|---|---|---|---|
| 厚度 | μm | 15 – 40 | Typical range |
| 热封温度 | °C | 100 – 140 | Grade dependent |
| 热封强度 | N/15mm | ≥ 3 | 120°C 0.3MPa 1s |
| Coefficient of Friction | – | 0.1 – 0.3 | Film to film |
| 雾度 | % | ≤ 2.5 | GB/T 2410 |
| 水蒸气透过量 | g/m²·24h | ≤ 4 | 38°C 90% RH |
| 封合形式 | – | One/Two-side | As specified |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
BOPP 珠光薄膜技术参数表 /
基础信息 /
- 执行标准 /
- QB/T 2713-2005
- 商品编码 /
- 3920201000
- 型号规格 /
- BOPP Pearlized 35µm
- 卷号 /
- PL231010003
- 原材料 /
- PP K8303 + Calcium Carbonate
- 生产日期 /
- 2023-10-10
- 测试日期 /
- 2023-10-13
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 参数 | Unit | Value | Notes |
|---|---|---|---|
| 厚度 | μm | 20 – 50 | Standard range |
| 密度 | g/cm³ | 0.55 – 0.75 | Lower than clear BOPP |
| 不透明度 | % | ≥ 75 | White opaque |
| 光泽度 | GU | 60 – 110 | Pearl luster |
| Corona Treatment | – | One side | ≥ 38 mN/m |
| 热封 | – | Both sides | Heat sealable |
| 表面电阻 | Ω | ≤ 10¹¹ | Antistatic |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
BOPET 透明薄膜技术参数表 /
基础信息 /
- 执行标准 /
- GB/T 16958-2013
- 商品编码 /
- 3920629000
- 型号规格 /
- BOPET Clear 12µm
- 卷号 /
- PE231120004
- 原材料 /
- PET Chip Wankai 8008
- 生产日期 /
- 2023-11-20
- 测试日期 /
- 2023-11-23
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 参数 | Unit | Value / Range | Standard |
|---|---|---|---|
| 厚度 | μm | 4.5 – 350 | GB/T 16958 |
| Tensile Strength MD | MPa | ≥ 150 | GB/T 1040 |
| Tensile Strength TD | MPa | ≥ 150 | GB/T 1040 |
| 雾度 | % | ≤ 3 | GB/T 2410 |
| 透光率 | % | ≥ 87 | GB/T 2410 |
| Thermal Shrinkage MD (150°C) | % | ≤ 1.5 | GB/T 12027 |
| O₂ Transmission Rate | cm³/m²·24h·atm | 50 – 150 | Unfilled grade |
| 幅宽 | mm | 250 – 5,000 | Custom |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
CPP 流延膜技术参数表 /
基础信息 /
- 执行标准 /
- GB/T 10003-2008
- 商品编码 /
- 3920209000
- 型号规格 /
- CPP 40µm
- 卷号 /
- CP231201005
- 原材料 /
- PP F401 / T30S
- 生产日期 /
- 2023-12-01
- 测试日期 /
- 2023-12-04
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 参数 | Unit | Value / Range | Notes |
|---|---|---|---|
| 厚度 | μm | 20 – 80 | Standard grades |
| Tensile Strength MD | N/15mm | ≥ 20 | GB/T 1040 |
| Heat Seal Temperature | °C | 120 – 160 | Grade dependent |
| 水蒸气阻隔 | g/m²·24h | ≤ 8 | 38°C 90% RH |
| 雾度 | % | ≤ 5 | GB/T 2410 |
| 蒸煮级 | – | 可供 | 121°C retort |
| 幅宽 | mm | 200 – 6,000 | Custom |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
POF 聚烯烃热收缩膜技术参数表 /
基础信息 /
- 执行标准 /
- GB/T 28118-2011
- 商品编码 /
- 3920999090
- 型号规格 /
- POF Shrink Film 19µm
- 卷号 /
- PF230715006
- 原材料 /
- PE + PP 共挤
- 生产日期 /
- 2023-07-15
- 测试日期 /
- 2023-07-18
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 测试项目 / | 单位 / | ASTM 测试标准 / | 12µm (微米) | 15µm (微米) | 19µm (微米) | 25µm (微米) |
|---|---|---|---|---|---|---|
| 拉伸性能 / | ||||||
| 纵向拉伸强度 / | N/mm^2 | D882 | 115 | 110 | 110 | 95 |
| 横向拉伸强度 / | N/mm^2 | D882 | 110 | 105 | 105 | 90 |
| 纵向断裂伸长率 / | % | D882 | 115 | 120 | 125 | 130 |
| 横向断裂伸长率 / | % | D882 | 110 | 115 | 115 | 125 |
| 撕裂性能 / | ||||||
| 纵向撕裂强度 / | gf | D1922 | 10.5 | 14.5 | 17.5 | 23.5 |
| 横向撕裂强度 / | gf | D1922 | 10.0 | 13.5 | 16.0 | 23.0 |
| 热封强度 / | ||||||
| 纵向电热丝热封强度 / | N/mm | F88 | 0.65 | 0.81 | 1.03 | 1.25 |
| 横向电热丝热封强度 / | N/mm | F88 | 0.68 | 0.86 | 1.06 | 1.30 |
| 摩擦系数 / | ||||||
| 静摩擦系数 / | – | D1894 | 0.25 | 0.22 | 0.22 | 0.25 |
| 动摩擦系数 / | – | D1894 | 0.24 | 0.20 | 0.24 | 0.26 |
| 光学性能 / | ||||||
| 雾度 / | % | D1003 | 2.2 | 2.6 | 3.2 | 3.9 |
| 清晰度 / | % | D1746 | 98.5 | 98.0 | 97.0 | 95.0 |
| 光泽度 (45°) / | % | D2457 | 85.5 | 87.0 | 83.5 | 81.5 |
| 阻隔性能 / | ||||||
| 氧气透过率 / | cc/m²/day | D3985 | 11300 | 10800 | 7200 | 5400 |
| 水蒸气透过率 / | gm/m²/day | F1249 | 45.5 | 38.5 | 26.5 | 22.5 |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
技术分析报告单 /
基础信息 /
- 执行标准 /
- QB/100
- 商品编码 /
- 39206290000
- 型号规格 /
- 光膜 PET 4.5µm (Glossy PET4.5)
- 卷号 /
- 20180910ABC-1
- 原材料 /
- MD642
- 生产日期 /
- 2018-09-10
- 测试日期 /
- 2018-09-18
- 测试环境 /
- 温度 (T): 30 ℃ / 相对湿度 (R): 56 %
| 测试项目 / | 单位 / | 平均值 / | 标准公差 / | 备注 / |
|---|---|---|---|---|
| 厚度 / | ||||
| 平均厚度 / | µm | 4.50 | 0.05 | |
| 厚度偏差 / | % | -0.2 | – | |
| 拉伸强度 / | ||||
| 纵向 (MD) | MPa | 230.8 | 7.0 | |
| 横向 (TD) | MPa | 267.4 | 6.1 | |
| 断裂伸长率 / | ||||
| 纵向 (MD) | % | 112.3 | 8.1 | |
| 横向 (TD) | % | 91.7 | 5.5 | |
| 热收缩率 / | ||||
| 纵向 (MD) | % | 1.62 | 0.18 | |
| 横向 (TD) | % | 0.40 | 0.10 | |
| 表面粗糙度 / | µm | 0.101 | 0.009 | |
| 摩擦系数 / | ||||
| 静摩擦系数 / | – | 0.46 | 0.04 | |
| 动摩擦系数 / | – | 0.41 | 0.02 | |
| 介电强度 / | ||||
| 直流击穿电压 / | V/mum | 542 | 47 | 最小值 (Min): 430 |
此信息代表我们对所做工作的最佳判断,但公司对使用本文所含信息或结论不承担任何责任。
This information represents our best judgment on the work done, but the company assumes no liability whatsoever in connection with the use of information or findings contained herein.
BOPP 预涂膜技术参数表 /
基础信息 /
- 执行标准 /
- QB/T 4658-2014
- 商品编码 /
- 3920201000
- 型号规格 /
- BOPP Thermal Laminating 25µm (Glossy/Matte)
- 卷号 /
- TL240110007
- 原材料 /
- BOPP + EVA Hot Melt Adhesive
- 生产日期 /
- 2024-01-10
- 测试日期 /
- 2024-01-13
- 测试环境 /
- 温度 (T): 23 ℃ / 相对湿度 (RH): 50 %
| 项目 / | 单位 / | 检验方法 / | 标准/典型值 (Standard / |
|---|---|---|---|
| BOPP 厚度 / | µm | GB/T6672 | (未明确标出) |
| 胶层厚度 / | µm | GB/T6672 | 12 | 11 | 08 | 08 |
| 平均厚度偏差 / | % | GB/T6672 | ±8 |
| 出膜量 / | m²/kg | – | 37.2 | 49.3 | 51.0 | 52.6 |
| 剥离强度 / | N/15mm | – | ≥ 0.6 |
| 拉伸强度 / | MPa | GB13022 | 纵向 (MD) ≥ 70 / 横向 (TD) ≥ 130 |
| 断裂伸长率 / | % | GB13022 | 纵向 (MD) ≤ 200 / 横向 (TD) ≤ 60 |
| 润湿张力 / | mN/m | GB/T10003 | 胶面 ≥ 42 / 表面 ≥ 42 |
| 热收缩率 / | % | GB/T10003 | 纵向 (MD) ≤ 1.5 / 横向 (TD) ≤ 1.0 |
| 雾度 / | % | GB2410 | < 5 |
免责声明 / Disclaimer: 上述信息是我们在特定条件下得到的结果,我们相信其可靠性,但不理解为保证值。我们建议购买者要根据使用的最终需要来确定其适用性。 (All details of the above information present the best condition available to us, and we believe them to be reliable, which can not be taken for guaranteed. We suggest that the suitability is determined by the really requirements of buyers.)